If your Jeep key fob isn’t being detected it can be a frustrating experience.
There are a few things that could be causing the problem but fortunately there are also a few things you can do to fix it.
One of the most common reasons for a Jeep key fob not being detected is a dead battery.
If your key fob’s battery is dead it’s not going to be able to communicate with your Jeep’s computer.
You’ll need to replace the battery in your key fob in order to get it working again.
Another common reason for a Jeep key fob not being detected is that it’s not properly programmed.
If your key fob isn’t programmed to work with your Jeep it’s not going to be able to communicate with your Jeep’s computer.
You’ll need to take your key fob to a Jeep dealer or a locksmith to have it programmed.
If neither of these solutions work it’s possible that your Jeep’s computer is the problem.
There are a few things that can cause your Jeep’s computer to not recognize your key fob.
One possibility is that your Jeep’s computer is outdated and needs to be updated.
Another possibility is that there’s a problem with the way your Jeep’s computer is wired.
If your Jeep’s computer is the problem you’ll need to take it to a Jeep dealer or a qualified mechanic to have it fixed.
Fortunately most of the time a Jeep key fob not being detected is a relatively easy problem to fix.
If you have a dead battery you can simply replace it.
If your key fob isn’t programmed to work with your Jeep you can take it to a Jeep dealer or a locksmith to have it programmed.
And if your Jeep’s computer is the problem you can take it to a Jeep dealer or a qualified mechanic to have it fixed.
What Does It Mean When Your Jeep Says “Key Fob Not Detected”?
You may have seen the message “Key Fob Not Detected” on your Jeep’s display.
This is a relatively common problem that can be caused by a number of different issues.
In this article we’ll take a look at what this message means and some of the potential causes.
First it’s important to note that this message is not necessarily indicative of a problem with your key fob.
It’s possible that the message is simply a warning that the key fob is not in close proximity to the Jeep.
This is most likely to happen if you leave your key fob in your purse or pocket when you get out of the Jeep.
If the message appears when you are actually trying to use the key fob then there may be an issue with the key fob itself.
One possibility is that the batteries in the key fob are low.
Another possibility is that the key fob’s signal is being blocked by something.
This could be something as simple as your Jeep’s metal body.
If you’ve determined that there is an issue with the key fob there are a few things you can try to fix the problem.
One option is to replace the batteries in the key fob.
Another option is to try moving the key fob closer to the Jeep.
If neither of these options work you may need to replace the key fob.
In some cases the problem may be with the Jeep itself.
It’s possible that the Jeep’s receiver is not compatible with the key fob.
This can usually be resolved by taking the Jeep to a dealership to have the receiver replaced.
If you’re still having trouble after trying all of these options it’s possible that the message is being caused by a more serious issue.
In this case it’s best to take the Jeep to a mechanic or dealership to have it diagnosed.
Reasons For Why Is The Jeep Key Fob Not Detected
If you’re a Jeep owner you know that the key fob is an essential part of the vehicle. It’s what allows you to start the engine lock and unlock the doors and even open the trunk.
But what happens when your Jeep key fob stops working? Why is the Jeep key fob not detected?
There are a few reasons why your Jeep key fob might not be working. Here are the top reasons:
1.
Dead Battery
One of the most common reasons why a key fob stops working is because the battery is dead. If you’ve had your Jeep for a while it’s likely that the original battery has simply reached the end of its lifespan. Luckily replacing the battery in your key fob is a pretty simple process.
2.
Faulty Key Fob
Another possibility is that the key fob itself is faulty. If you’ve dropped your key fob or it’s been exposed to water it’s possible that the circuitry inside has been damaged. In this case you’ll need to get a new key fob from your Jeep dealer.
3.
Wrong Key Fob
If you have more than one Jeep key fob it’s possible that you’re using the wrong one. Each key fob is coded to work with a specific Jeep so using the wrong key fob will prevent the Jeep from recognizing it. Make sure you’re using the correct key fob for your Jeep.
4.
Jeep’s Receiver is Damaged
The receiver is the component of the Jeep that reads the signal from the key fob. If the receiver is damaged it might not be able to read the signal from the key fob. In this case you’ll need to have the receiver replaced by a Jeep dealer.
5.
Out of Range
One final possibility is that the key fob is simply out of range. If you’re too far away from the Jeep the key fob’s signal might not be strong enough to reach the receiver. In this case you’ll just need to get closer to the Jeep.
If your Jeep key fob isn’t working don’t panic.
There are a few possible reasons why. Start by checking the battery and making sure you’re using the correct key fob. If those things don’t fix the problem you’ll need to take your Jeep to a dealer for further diagnosis.
5 Ways To Fix Your Jeep Key Fob That Is Not Detected
If your Jeep key fob is not detected there are a few things that you can do to try and fix the issue.
1.
Check the batteries
The first thing that you should do is check the batteries. If the batteries are dead then the key fob will not be detected. You should replace the batteries and see if that fixes the issue.
2.
Check the connection
Another thing that you can do is check the connection between the key fob and the Jeep. If the connection is loose then the key fob will not be detected. You should check the connection and see if it is tight.
3.
Check the antenna
The next thing that you can do is check the antenna. If the antenna is not working then the key fob will not be detected. You should check the antenna and see if it is working.
4.
Check the transponder
The last thing that you can do is check the transponder. If the transponder is not working then the key fob will not be detected. You should check the transponder and see if it is working.
5.
Check the Jeep
The last thing that you can do is check the Jeep itself. If the Jeep is not working then the key fob will not be detected. You should check the Jeep and see if it is working.
How To Start Your Jeep With A Dead Key Fob
If you’ve ever had a dead key fob you know the frustration of not being able to get into your Jeep.
Even if you have a spare key it’s not always convenient to use it.
Here’s a quick and easy way to start your Jeep with a dead key fob.
First make sure your Jeep is in Park.
If it’s not the starter won’t engage.
Next locate the key fob.
It’s usually on the driver’s side near the steering wheel.
If the key fob is dead you’ll need to use the emergency key.
This is usually a metal key that’s hidden inside the key fob.
To find it look for a small slot or hole on the key fob.
Insert the key into the slot and push it in until you feel it click.
Once the key is inserted turn it to the On position.
You should hear the Jeep’s engine start.
If the key fob is still dead you may need to replace the battery.
To do this remove the key fob from the key slot.
There will be a small Phillips head screw holding the battery cover in place.
Remove the screw and the cover.
With the cover off you’ll see the battery.
Use a small flathead screwdriver to pry it out.
Now take your new battery and insert it into the key fob.
Replace the cover and screw.
Once the new battery is in place try starting your Jeep again.
If the key fob is still dead you may need to consult a Jeep dealer or a qualified automotive locksmith.